manualshive.com logo in svg

Chrysler 300 SRT 2010, Owner'S Manual, Page: 281 / 465

Share
Download
Chrysler 300 SRT 2010 Owner'S Manual Download Page 281

CAUTION!

To prevent damage to the starter, wait 10 to 15 sec-
onds before trying again.

After Starting

The idle speed is controlled automatically and it will
decrease as the engine warms up.

ENGINE BLOCK HEATER — IF EQUIPPED

The engine block heater warms the engine, and permits
quicker starts in cold weather. Connect the cord to a
standard 110-115 Volt AC electrical outlet with a
grounded, three-wire extension cord.

The engine block heater cord is routed under the hood on
the driver side of the vehicle. It has a removable cap that
is located on the driver side of the Integrated Power
Module.

WARNING!

Remember to disconnect the cord before driving.
Damage to the 110-115 Volt electrical cord could cause
electrocution.

AUTOMATIC TRANSMISSION

CAUTION!

Damage to the transmission may occur if the follow-
ing precautions are not observed:

•

Shift into PARK only after the vehicle has come to
a complete stop.

•

Shift into or out of REVERSE only after the
vehicle has come to a complete stop and the engine
is at idle speed.

(Continued)

280

STARTING AND OPERATING

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments