Home
/
Chrysler
/
300 SRT 2010
/
Owner'S Manual

Chrysler 300 SRT 2010, Owner'S Manual, Page: 294 / 465

Share

Page: 294 / 465

Chrysler 300 SRT 2010 Owner'S Manual Download Page 294

WARNING!

•

Driving through standing water limits your vehi-
cle’s traction capabilities. Do not exceed 5 mph
(8 km/h) when driving through standing water.

•

Driving through standing water limits your vehi-
cle’s braking capabilities, which increases stop-
ping distances. Therefore, after driving through
standing water, drive slowly and lightly press on
the brake pedal several times to dry the brakes.

•

Getting water inside your vehicle’s engine can
cause it to lock up and stall out, and leave you
stranded.

•

Failure to follow these warnings may result in
injuries that are serious or fatal to you, your
passengers, and others around you.

POWER STEERING

The standard power steering system will give you good
vehicle response and increased ease of maneuverability
in tight spaces. The system will provide mechanical
steering capability if power assist is lost.

If for some reason the power assist is interrupted, it will
still be possible to steer your vehicle. Under these condi-
tions, you will observe a substantial increase in steering
effort, especially at very low vehicle speeds and during
parking maneuvers.

NOTE:

•

Increased noise levels at the end of the steering wheel
travel are considered normal and do not indicate that
there is a problem with the power steering system.

5

STARTING AND OPERATING

293

«
...
292
293
294
295
296
...
»

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments