manualshive.com logo in svg

Chrysler 300 SRT 2010, Owner'S Manual, Page: 443 / 465

Share
Download
Chrysler 300 SRT 2010 Owner'S Manual Download Page 443

Temperature Grades

The temperature grades are A (the highest), B, and C,
representing the tire’s resistance to the generation of heat
and its ability to dissipate heat, when tested under
controlled conditions on a specified indoor laboratory
test wheel. Sustained high temperature can cause the
material of the tire to degenerate and reduce tire life, and
excessive temperature can lead to sudden tire failure. The
grade C corresponds to a level of performance, which all
passenger car tires must meet under the Federal Motor
Vehicle Safety Standard No. 109. Grades B and A repre-
sent higher levels of performance on the laboratory test
wheel, than the minimum required by law.

WARNING!

The temperature grade for this tire is established for
a tire that is properly inflated and not overloaded.
Excessive speed, under-inflation, or excessive load-
ing, either separately or in combination, can cause
heat buildup and possible tire failure.

442

IF YOU NEED CONSUMER ASSISTANCE

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments