Home
/
Chrysler
/
300 SRT 2010
/
Owner'S Manual

Chrysler 300 SRT 2010, Owner'S Manual, Page: 153 / 465

Share

Page: 153 / 465

Chrysler 300 SRT 2010 Owner'S Manual Download Page 153

POWER TILT/TELESCOPING STEERING COLUMN
— IF EQUIPPED

This feature allows you to tilt the steering column
upward or downward. It also allows you to lengthen or
shorten the steering column. The power tilt/telescoping
steering column lever is located below the multifunction
lever on the steering column.

To tilt the steering column, move the lever up or down as
desired. To lengthen or shorten the steering column, pull
the lever toward you or push the lever away from you as
desired.

NOTE:

For vehicles equipped with Driver Memory

Seat, you can use your Remote Keyless Entry (RKE)
transmitter or the memory switch on the driver’s door
trim panel to return the tilt/telescopic steering column to
pre-programmed positions. Refer to “Driver Memory
Seat” in this section.

Power Tilt/Telescoping Steering

152

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

«
...
151
152
153
154
155
...
»

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments