manualshive.com logo in svg

Chrysler 300 SRT 2010, Owner'S Manual, Page: 191 / 465

Share
Download
Chrysler 300 SRT 2010 Owner'S Manual Download Page 191

mileage was before the repair or service. It is a good idea
for you to make a record of the odometer reading before
the repair/service, so that you can be sure that it is
properly reset, or that the door jamb sticker is accurate if
the odometer must be reset at zero.

This display shows the Electronic Vehicle Information
Center (EVIC) messages when the appropriate conditions
exist. (Refer to “Electronic Vehicle Information Center
(EVIC)” for further information).

Loose Fuel Filler Cap Message

If the vehicle diagnostic system determines that the fuel
filler cap is loose, improperly installed, or damaged, a
“Check Gascap” message will display in the odometer
display area. Tighten the fuel filler cap properly and
press the TRIP ODOMETER button to turn off the
message. If the problem continues, the message will
appear the next time the vehicle is started.

A loose, improperly installed, or damaged fuel filler cap
may also turn on the Malfunction Indicator Light (MIL).

7. Tachometer

The red segments indicate the maximum permissible
engine revolutions per minute (RPM x 1000) for each gear
range. Ease up on the accelerator before reaching the red
area.

8. Engine Temperature Warning Light

This light will turn on and a single chime will
sound to warn of an overheated engine condition.
When this light turns on, the engine temperature

is critically hot. The vehicle should be turned OFF
immediately and serviced as soon as possible.

9. Anti-Lock Brake (ABS) Light

This light monitors the Anti-Lock Brake System
(ABS). The light will turn on when the ignition

switch is placed in the RUN position and may stay on for
as long as four seconds.

190

UNDERSTANDING YOUR INSTRUMENT PANEL

Summary of Contents for 300 SRT 2010


















































































































































































































































































































































































































































































Reviews:

No comments