15
3. distance "
H" smaller than 300 mm: wire mesh fencing "I" or punched
metal plating "
L" with an opening which does not allow the passage
of a
12 mm diameter sphere "M" must be fitted.
The wires of the mesh "
I" must not have a cross-section of less than
2,5 mm
2
and the punched metal plating "
L" must not have a thick-
ness of less than
1,2 mm.
Protection is not necessary for the area "
P" if the fixed structure with
railings or bars is over
2,5 m above the ground.
- check the gate components, replace any worn or damaged parts
and then lubricate them.
- using a spirit level "
N" check that the castor guide is in square.
- the upper runner guide "
O" must have the correct play for the gate
and must not inhibit the gate’s sliding action.
- check that a mechanical travel limit "
Q" (absolutely necessary) has
been fitted in the opening direction and that it corresponds to the
maximum travel distance "
P" of the gate.
The travel limit must guarantee anti-derailment and gate stability.
Warning! It is the installer’s responsibility to check all criti-
cal danger points, to take action and to install any devices
needed to guarantee the safety of all people using the gate
(risk analysis).
• The geared motor can be positioned either to the left or to the right
of the passageway.
Important: read the paragraph "INSTRUCTIONS
FOR POSITIONING THE UNIT".
Anchoring the unit (fig. 4, 5, 6)
Important! Check the exact anchoring position with respect to the
alignment of the sliding gate.
• Run the piping and connection wires to the position where the motor
is to be installed.
• Attach the anchor bolts to the base plate "
A" allowing them to protrude
by
40 mm and then tighten down using the supplied M8 nuts.
• Prepare a cement plinth, in the position where the motor is to be
installed, with a depth of
350 mm (the base should protrude by
about
25 mm to avoid damage by pools of water building up under
the appliance).
• Insert the base plate making sure that:
- the electrical cables pass through the hole "
b";
- the anchor bolts "
C" are immersed into the cement base and the
base plate is perfectly level;
- the four protruding
50 mm threaded bolts are perpendicular to the
base plate;
- the surface area of the base plate is clean and free of cement resi-
due.
INSTALLATION INSTRUCTIONS
If the runner guide already exists the cement base should be extended
to take in part of the runner guide foundation. This will stop the two
foundations from giving way separately.
- Unscrew the four
M8 nuts on the four threaded bolts (previously used to
block the anchor bolts) and leave a space of
15 mm between the anchor
plate and the base of the motor. Then insert the four washers and allow
them to rest on the nuts.
- Position the geared motor over the four threaded bolts and allow it to
rest on the four washers.
- Fasten it to the base using the other four washers and adjustment nuts
supplied with the kit, making sure that the unit remains perfectly level
and stable.
This will allow you to adjust the height and position of the motor later
on.
SCALA: 1:2
Prodotti (plinto 350 mm)
SL424EbSb
16-06-2006
DI0409
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
VISTA DI FIANCO CON MOTORE
2 mm
15 mm
25
325
SCALA: 1:2
Prodotti (plinto 350 mm)
SL424EbSS
08-06-2005
DI0408
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
VISTA DI FIANCO SENZA MOTORE
25
145
70
40
15
325
SCALA: 1:2
Prodotti Technocity
SL4024
08-06-98
DI0065
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
CONTROPIASTRA SL4024
40 mm
M8
A
b
C
SCALA: 1:2
Prodotti Technocity
SL424E
17-06-2004
DI0344
Description :
Product Code :
Date :
Drawing number :
P.J.Heath
CARDIN ELETTRONICA S.p.A - 31020 San Vendemiano (TV) Italy - via Raffaello, 36 Tel: 0438/401818 Fax: 0438/401831
Draft :
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
VISTA CONTROPIASTRA SL4024
70
4
3
5
2
1
5
300
130
6
5
4
Fitting the toothed rack
- release the geared motor (fig. 8), lay the first stretch of the toothed rack
on the pinion and fix it to the gate, then fasten down all the other parts
along the entire length of the gate.
- after having fastened the toothed rack, realign the pinion (play of
1 to 2
mm between the toothed runner and the pinion) using the positioning
nuts at the base of the geared motor. This action will prevent the weight
of the sliding gate from damaging the unit when working.
Attention!
You must respect the distance of
15 mm between the anchor
plate and the base of the motor.
Summary of Contents for SL 424EBS
Page 50: ...50 NOTES...
