Canon imagePRESS C7000VP Series Trouble Shooting Information Download

Page: 59 / 137

Trouble Shooting Information for C7000VP series

Page 59

Rev. 2.0

2010/09/17

2.12

Noise occurred at operating the refresh roller -> New item



Description

Noise occurs when driving the refresh roller.



Cause

The screw that secures the roll retaining plate (FC7-4948-000) at the pressure assembly of the

refresh roller loosens and there generates a state of insufficient pressuring of the refresh roller

against the fixing roller; the refresh roller is driven with insufficient gear engagement for driving

the refresh roller.



Field Remedy

Tighten the screw loosened as described above.

The roll retaining plate may have been deformed.

In this case, replace the part.

(Reference)

Change into the locking screw (FU5-9235-000) is planned.
When the parts are prepared, Service Information will be issued.

Summary of Contents for imagePRESS C7000VP Series










































































































































Search results

Summary of Contents for imagePRESS C7000VP Series

Reviews:

Related manuals for imagePRESS C7000VP Series

Brands by name

Popular brands

Canon imagePRESS C7000VP Series, Trouble Shooting Information

Search results

Summary of Contents for imagePRESS C7000VP Series

Reviews:

Related manuals for imagePRESS C7000VP Series

Brands by name

Popular brands