Canon imagePRESS C7000VP Series Trouble Shooting Information Download Page 60

Page: 60 / 137

Trouble Shooting Information for C7000VP series

Page 60

Rev. 2.0

2010/09/17

2.13

The magenta developing assembly is not activated -> New item



Cause

Breakage of the bearing at the developing rail assembly and the gear of the developing drive

assembly



Field Remedy

Check the state of breakage and replace the developing rail assembly and/or developing drive

assembly.

Check whether the measures in ‘2.9 Noise from around developing drive assembly/Cracked

developing drive gear’ have been implemented.

2.14

Breakage of the splatter prevention sheet at the end of the

developing assembly

-> New item



Description

Abrasion against the drum causes the sheet to be broken.

Summary of Contents for imagePRESS C7000VP Series










































































































































Search results

Summary of Contents for imagePRESS C7000VP Series

Reviews:

Related manuals for imagePRESS C7000VP Series

Brands by name

Popular brands

Canon imagePRESS C7000VP Series, Trouble Shooting Information

Search results

Summary of Contents for imagePRESS C7000VP Series

Reviews:

Related manuals for imagePRESS C7000VP Series

Brands by name

Popular brands