Canon imagePRESS C7000VP Series Trouble Shooting Information Download

Page: 82 / 137

Trouble Shooting Information for C7000VP series

Page 82

Rev. 2.0

2010/09/17

3.21

Starter overflow

* Same actions should be taken for tiger stripe/coating failure/boomerang



Description

Although the following measures are implemented for preventing toner scattering, this symptom

may recur depending on the conditions of use at users (image duty or print volume).



Software installation of system Ver.71.02 + DconVer.35.03



Service mode (Level 1) COPIER> OPTION> BODY> DEV-SP1> 00000110



Installation of ACR spacer/Spatter prevention sheet



Field Remedy

1. Check toner density in the developing assembly in service mode (Level 1) COPIER>

DISPLAY> DENS> DENS-Y/M/C/K.

2. If toner density di1% or higher, change the setting as follows.

Service mode (Level2) COPIER> ADJUST> DENS> HLMT-PTY/M/C/K



If it is ‘4’ at this point, change it to ‘9’.



If it is ‘9’ at this point, change it to ‘10’.

* Note that the density will be degraded as a negative effect.

3. If toner density displays lower than +1%, change the setting as follows.

Service mode (Level2) COPIER> ADJUST> DENS> P-TG-Y/M/C/K



Input a value adding ‘10’ to current value.

4. Perform the operations in order.



Clean around the developing assembly and wipe the surface of ATR patch sensor with

lint-free paper moistened with alcohol



Additional Functions > Adjustment/Cleaning > wire cleaning



Print 100 sheets of PG10 with LDR paper



Additional Functions > Adjustment/Cleaning > wire cleaning



Additional Functions > Adjustment/Cleaning > Auto gradation adjustment

Spatter Prevention Sheet

Summary of Contents for imagePRESS C7000VP Series










































































































































Search results

Summary of Contents for imagePRESS C7000VP Series

Reviews:

Related manuals for imagePRESS C7000VP Series

Brands by name

Popular brands

Canon imagePRESS C7000VP Series, Trouble Shooting Information

Search results

Summary of Contents for imagePRESS C7000VP Series

Reviews:

Related manuals for imagePRESS C7000VP Series

Brands by name

Popular brands