Canon imagePRESS C7000VP Series Trouble Shooting Information Download | Manualshive

Page: 135 / 137

background image

Trouble Shooting Information for C7000VP series

Page 135

Rev. 2.0

2010/09/17

Appendix 3 Points to Note When Replacing Primary/Secondary Fixing

Intermediate Unit

Fixing intermediate unit (Service Part) mainly consists of the following parts:

- Fixing assembly frame
- Fixing internal driver PCB
- Fixing drive assembly
- Fixing roller
- Fixing heater
- Refresh roller
- Fixing belt separation roller fixing spring

MEMO:

The refresh roller and the fixing belt separation roller fixing spring are included in the package

of the fixing intermediate unit. They are not attached to the fixing intermediate unit. Note that

the fixing belt separation roller fixing spring is included only in a package of the primary fixing

intermediate unit.

Be sure to attach the following parts, which are included in the package of a new fixing

intermediate unit, to the new fixing intermediate unit.



Refresh roller



Fixing belt separation roller fixing spring (for the primary fixing assembly only)

Be sure to remove the following parts from the old fixing assembly and reattach them to the new

fixing intermediate unit.

-Fixing upper cover
-Fixing web unit
-External heat roller unit
-Fixing belt unit (primary fixing assembly), or Pressure roller unit (secondary fixing assembly)
-Internal delivery unit
-Short connectors (for detecting location)

Attach the 2 short connectors [1] (for detecting location) to the drawer unit in the new fixing

intermediate unit. The short connectors (for detecting location) need to be removed/reattached

in case of replacing a drawer unit.

«
...
133
134
135
136
137
»

Summary of Contents for imagePRESS C7000VP Series










































































































































Reviews:

No comments

Related manuals for imagePRESS C7000VP Series

ImageCLASS MF3240 Series

Brand: Canon Pages: 62

ImageCLASS MF4270

Brand: Canon Pages: 226

imageCLASS D660

Brand: Canon Pages: 8

ImageCLASS MF3240 Series

Brand: Canon Pages: 136

Color imageRUNNER C5180 Series

Brand: Canon Pages: 851

imageCLASS D320

Brand: Canon Pages: 121

imageCLASS MF212w

Brand: Canon Pages: 236

imageCLASS D760

Brand: Canon Pages: 82

imageclass LBP251dw

Brand: Canon Pages: 72

ImageCLASS MF4270

Brand: Canon Pages: 248

ImageCLASS MF4270

Brand: Canon Pages: 36

imageCLASS D760

Brand: Canon Pages: 8

imageCLASS MF4100 Series

Brand: Canon Pages: 140

imageclass LBP251dw

Brand: Canon Pages: 116

imageCLASS D860

Brand: Canon Pages: 73

imageCLASS D1320

Brand: Canon Pages: 36

ImageCLASS MF3240 Series

Brand: Canon Pages: 15

imageCLASS D550

Brand: Canon Pages: 116

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands