manualshive.com logo in svg

Canon FAX L290, User Manual, Page: 158 / 229

Share
Download
Canon FAX L290 User Manual Download Page 158

13-2

Troubleshooting

Chapter 13

Clearing Jams

Jams in the ADF

When a document jams or misfeeds in the ADF, the LCD displays 

CHECK

DOCUMENT

.

Follow this procedure to clear the document jam:

n

You do not need to unplug the FAX when clearing document jams.

1

Press 

Stop

.

2

Use both hands to gently open the
operation panel.

• It only opens partially.
• Do not try to pull the document out

without opening the operation panel
since you may tear or smudge the
document.

3

While holding the operation panel open,
remove the document.

• Pull it gently in either direction.
• If a multipage document is loaded,

remove the entire document from the
ADF.

n

If the paper does not pull out
easily, do not force it. Contact your
local authorised Canon dealer or
the Canon help line.

4

When you are finished, close the
operation panel by pressing it down
from the centre.

• Be sure to close the operation panel

until it locks into place, or the unit will
not function properly.

Summary of Contents for FAX L290






































































































































































































































Reviews:

No comments