Home
/
Canon
/
FAX L290
/
User Manual

Canon FAX L290, User Manual, Page: 148 / 229

Share

Page: 148 / 229

Canon FAX L290 User Manual Download Page 148

12-2

Maintenance

Chapter 12

Periodic Cleaning

This section describes the necessary cleaning procedures for your FAX. Please note
the following before cleaning your unit:

• Be sure to disconnect the power cord before cleaning the FAX. Since documents in

memory are erased when the power is disconnected, print or send any documents
stored in memory before disconnecting the power cord (

1

p. 9-5).

• Do not use tissue paper, paper towels, or similar materials for cleaning; they can stick

to the components or generate static charges.

c

Never use volatile liquids such as thinners, benzene, acetone, or any other chemical
cleaner to clean the interior of the FAX; these can damage the unit’s components.

Cleaning the FAX’s Exterior

Follow this procedure to clean the FAX’s outer casing:

1

Disconnect the power cord from the
FAX.

2

Wipe the FAX’s exterior with a clean,
soft, lint-free cloth moistened with
water or diluted dishwashing detergent
solution.

3

When you are finished, reconnect the
power cord.

«
...
146
147
148
149
150
...
»

Summary of Contents for FAX L290






































































































































































































































Reviews:

No comments