Cambium Networks PTP 820F Installation Manual Download Page 7 | Manualshive

Page: 7 / 46

background image

vii

phn-4750_003v006

About This Installation Guide

This guide describes the PTP 820F installation procedures. This guide also provides initial
configuration instructions for once the hardware installation is complete.

This guide contains the following chapters:

Before You Start

PTP 820F Hardware Overview

Preparing for Installation

Installing the PTP 820F IDU

Connecting the Power Cable

Power Supply Notes

IDU-RFU Cable Connection

Performing Initial Configuration

Acceptance and Commissioning Procedures

What You Should Know

A PTP 820F system consists of an PTP 820F indoor unit (IDU) and one or more radio frequency
units (RFUs). This manual provides instructions for the installation of the PTP 820F IDU only. Some
features described in this manual may not be available in the current release. Consult the Release
Notes for the functionality supported in the specific release you are using.

Related Documents

•

PTP 820F Technical Description

•

User Guide for PTP 820F, and PTP 820G

•

PTP 820 Series MIB Reference

•

RFU-D Installation Guide

•

RFU-S Installation Guide

•

RFU-D-HP Installation Guide

Contacting Cambium Networks

Support website:

http://www.cambiumnetworks.com/support

Main website:

http://www.cambiumnetworks.com

Sales enquiries:

[email protected]

Support enquiries:

[email protected]

Repair inquiries

[email protected]

«
...
5
6
7
8
9
...
»

Summary of Contents for PTP 820F















































Reviews:

No comments

Related manuals for PTP 820F

Brand: D-Link Pages: 10

Brand: Nayar Systems Pages: 37

Brand: Accuphase Pages: 2

Brand: ADTRAN Pages: 2

AMB-VDX3H1 Series

Brand: Acrosser Technology Pages: 4

ZyXEL EES-1024AF

Brand: ZyXEL Communications Pages: 99

Brand: Planet Pages: 20

Brand: SeaLevel Pages: 17

Brand: LogLogic Pages: 30

Brand: Mercusys Pages: 35

Brand: UfiSpace Pages: 34

Brand: Rane Pages: 128

Brand: Acard Pages: 34

Brand: Shure Pages: 113

Brand: Quantum Pages: 7

AT32F421 Series

Brand: ARTERY Pages: 337

LIQMAX III ELC-LMT120-ARGB

Brand: ENERMAX Pages: 32

Brand: Matrix Switch Corporation Pages: 54

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands