Cambium Networks PTP 820F Installation Manual Download Page 40

Page: 40 / 46

10-29

phn-4750_003v006

SITE ACCEPTANCE CHECKLIST

Cable connected securely to RFU and IDU

Cable connector is weather-proofed (sealed) at the RFU

At the RFU, cable has a service/drip loop to prevent moisture from
entering the connector

Cable is secured using suitable restraints to fixed points at regular intervals
(0.5 m recommended)

Cable has no sharp bends, kinks, or crushed areas. All bends are per
manufacturer specifications

Grounding/lightning protection is as per site specifications

Lightning protection type and model:

Cable point-of-entry to building/shelter is weather-proof

Cable ends are properly labeled

6. FLEXIBLE WAVEGUIDE

Overall flexible WG length:

Flexible WG type:

Flexible WG is connected securely to RFU and Antenna

Flexible WG connector is weather-proofed (sealed) at the RFU

At the RFU, the flexible WG has a service/drip loop to prevent moisture
from entering the connector

Flexible WG is secured using suitable restraints to fixed points at regular
intervals (0.5 m recommended)

Flexible WG has no sharp bends, kinks, or crushed areas. All bends are per
manufacturer specifications

Flexible WG point-of-entry to building/shelter is weather-proof

Flexible WG ends are properly labeled

7. INDOOR UNIT

IDU is securely mounted to the rack

IDU is located in a properly ventilated environment

IDU fans are functional and air flow to the fans is not disrupted

IDU and rack are grounded as per site specifications

Summary of Contents for PTP 820F















































Search results

Summary of Contents for PTP 820F

Reviews:

Related manuals for PTP 820F

Brands by name

Popular brands

Cambium Networks PTP 820F, Installation Manual

Search results

Summary of Contents for PTP 820F

Reviews:

Related manuals for PTP 820F

Brands by name

Popular brands