Cambium Networks PTP 820F Installation Manual Download Page 39

Page: 39 / 46

10-28

phn-4750_003v006

SITE ACCEPTANCE CHECKLIST

Mount is grounded as per site specifications

All steelwork is Galvanized or Stainless Steel as appropriate

3. ANTENNA

Antenna type (model and size):

Antenna is securely fixed to mount

Antenna is grounded as per site specifications

Antenna sway braces are installed correctly (where applicable)

Antenna Radome is securely fitted (where applicable)

Water drain plugs are fitted and removed, as appropriate

Antenna sealing O-Ring is properly fitted and not damaged

Antenna/Launch unit polarization is as per link requirements

4. RADIO FREQUENCY UNIT (RFU)

Type of RFU mount:

(Direct or Remote
mount)

RFU is securely mounted to the antenna or pole

RFU is grounded as per installation instructions

RFU‘s polarization is as per link requirements

RFU is installed properly and has no physical damage

For Remote-Mount Only:

Remote mount kit is securely mounted to the pole

Flexible waveguide has no physical damage and connectors are sealed

All flexible waveguide bolts are secured using washers and lock-washers,
as appropriate

Flexible waveguide is secured to the pole

5. COAX CABLE

Overall cable length

Cable type

N-Type connectors assembled properly on the cable

Summary of Contents for PTP 820F















































Search results

Summary of Contents for PTP 820F

Reviews:

Related manuals for PTP 820F

Brands by name

Popular brands

Cambium Networks PTP 820F, Installation Manual

Search results

Summary of Contents for PTP 820F

Reviews:

Related manuals for PTP 820F

Brands by name

Popular brands