Cambium Networks PTP 820F Installation Manual Download Page 26 | Manualshive

Page: 26 / 46

background image

4-15

phn-4750_003v006

Replacing an PTP 820F IDU or SM-Card

If you should need to replace the PTP 820F IDU, you must first remove the SM-Card Cover so that
you can insert it into the new IDU.

The SM-Card holds the configuration and software for the IDU. The SM-Card is embedded in the SM-
Card plastic cover that is located under the SM-card aluminum cover.

To remove the SM-Card:

1.

Switch the unit power off.

2.

Loosen the 2 screws of the SM-Card’s aluminum cover and remove it from the IDU.

3.

Loosen the 2 screws of the SM-Card Plastic Cover and gently remove it from the IDU.

«
...
24
25
26
27
28
...
»

Summary of Contents for PTP 820F















































Reviews:

No comments

Related manuals for PTP 820F

Brand: E-Lins Pages: 59

Brand: E-Lins Pages: 11

Brand: E-Lins Pages: 9

Brand: E-Lins Pages: 5

Network Video Recorders

Brand: e-Line Technology Pages: 34

Device Server UDS 10

Brand: Lantronix Pages: 8

EXPANSION CARD X-DANTE

Brand: Behringer Pages: 65

RIPWAVE 40-00460-00R

Brand: Navini Networks Pages: 35

Brand: Paradyne Pages: 10

Brand: Ubiquiti Pages: 20

Brand: Teletronics International Pages: 57

Brand: NETGEAR Pages: 142

Brand: Kontron Pages: 98

Brand: Atmel Pages: 2

8-Port 10/100Mbps Fast Ethernet Switch

Brand: Amer.com Pages: 14

Brand: Cypress Semiconductor Pages: 26

TeleMyo 2400T V2

Brand: Noraxon Pages: 52

N-FXE 02B Series

Brand: Lantronix Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands