Cambium Networks PTP 820F Installation Manual Download Page 24 | Manualshive

Page: 24 / 46

background image

4-13

phn-4750_003v006

Chapter 4

Installing the PTP 820F IDU

This section provides instructions for installing a PTP 820F IDU.

Figure 6 IDU (Full Configuration)

Kits Required to Perform the Installation

Description

Quantity

PTP 820F chassis

1

19" rack / sub-rack

1

SM-Card Cover

1

Tools

•

Philips screwdriver

•

Flat screwdriver

Installing the PTP 820F IDU in the Rack (19")

Insert and hold the PTP 820F IDU in the rack, as shown in the following figures. Use four screws (not
supplied with the installation kit) to fasten the IDU to the rack.

«
...
22
23
24
25
26
...
»

Summary of Contents for PTP 820F















































Reviews:

No comments

Related manuals for PTP 820F

TokenLink 3C359B

Brand: 3Com Pages: 4

TokenLink 3C359B

Brand: 3Com Pages: 8

TokenLink 3C339

Brand: 3Com Pages: 2

EtherLink 3C985B-SX

Brand: 3Com Pages: 44

Brand: 3Com Pages: 88

Brand: 3Com Pages: 2

Brand: 3Com Pages: 111

TokenLink 3C359

Brand: 3Com Pages: 4

Brand: 3Com Pages: 74

Brand: 3Com Pages: 6

Brand: F5 Pages: 2

Brand: F5 Pages: 90

Brand: F5 Pages: 47

Brand: H3C Pages: 21

Adapter Bracket

Brand: Paradyne Pages: 1

Brand: Lorex Pages: 186

Brand: NETGEAR Pages: 14

Brand: Lucent Technologies Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands