Cambium Networks cnPilot R200 User Manual Download Page 93

Page: 93 / 151

Chapter 3: Advanced Configuration

FXS1

Page

DND

Enable/Disable DND (do not disturb).
If enable, any phone call cannot arrive at the device; default is disable.

Speed Dial

Enter the speed dial phone numbers.
Dial *74 to active speed dial function.
Then press the speed dial numbers, for example, press 2, phone dials
075526099365 directly.

Advanced

Table 54 Advanced

Field Name

Description

Domain Name
Type

If or not use domain name in the SIP URI.

Carry Port
Information

If or not carry port information in the SIP URI.

Signal Port

The local port of SIP protocol, default is 5060.

DTMF Type

Choose the DTMF type from Inbound, RFC2833 and SIP INFO.

Summary of Contents for cnPilot R200
























































































































































Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands

Cambium Networks cnPilot R200, User Manual

Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands