Cambium Networks cnPilot R200 User Manual Download Page 111

Page: 111 / 151

Chapter 3: Advanced Configuration

Administration

Page

109

Field Name

Description

User type

Choose the user type from admin user and normal user and basic user.

New User Name

You can modify the user name, set up a new user name

New Password

Input the new password

Confirm Password

Input the new password again

Language

Select the language for the web, the device support Chinese, English,
and Spanish and so on.

Management using
VPN

Remote Web Login

Enable/Disable remote Web login

Allow wireless host

To allow all the wireless clients connected to the cnPilot Home Router
to access the management interface

Local Web Port

Set the port value which is used to login from Internet port and PC
port, default is 80.

Summary of Contents for cnPilot R200
























































































































































Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands

Cambium Networks cnPilot R200, User Manual

Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands