Cambium Networks cnPilot R200 User Manual Download Page 92

Page: 92 / 151

Chapter 3: Advanced Configuration

FXS1

Page

Silence Support

Enable/Disable silence support.

Echo Cancel

Enable/Disable echo cancel. By default, it is enabled.

Auto Gain Control

Enable/Disable auto gain.

T.38 Enable

Enable/Disable T.38

T.38 Redundancy

Enable/Disable T.38 Redundancy

T.38 CNG Detect Enable Enable/Disable T.38 CNG Detect

gpmd attribute Enable

Enable/Disable gpmd attribute.

Supplementary Service Subscription

Table 53 Supplementary service

Field Name

Description

Call Waiting

Enable/Disable Call Waiting

Hot Line

Fill in the hotline number.
Pickup handset or press hands-free or headset button, the device will dial
out the hotline number automatically.

MWI Enable

Enable/Disable MWI (indicates message waiting). If the user needs to user
voice mail, please enable this feature.

MWI Subscribe
Enable

Enable/Disable MWI Subscribe

Voice Mailbox
Numbers

Fill in the voice mailbox phone number, Asterisk platform, for example, its
default voice mail is *97

VMWI Serv

Enable/Disable VMWI service.

Summary of Contents for cnPilot R200
























































































































































Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands

Cambium Networks cnPilot R200, User Manual

Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands