Cambium Networks cnPilot R200 User Manual Download Page 90

Page: 90 / 151

Chapter 3: Advanced Configuration

FXS1

Page

FXS1

SIP Account

Basic

Set the basic information provided by your VOIP Service Provider, such as Phone Number,
Account, password, SIP Proxy and others.

Table 51 SIP Account – Basic

Field Name

Description

Line Enable

Enable/Disable the line.

Peer To Peer

Enable/Disable PEER to PEER.
If enabled, SIP-1 will not send register request to SIP server; but in Status/
SIP Account Status webpage, Status is Registered; lines 1 can dial out,
but the external line number cannot dial line1.

Proxy Server

The IP address or the domain of SIP Server

Outbound Server

The IP address or the domain of Outbound Server

Backup Outbound
Server

The IP address or the domain of Backup Outbound Server

Proxy port

SIP Service port, default is 5060

Outbound Port

Outbound Proxy’s Service port, default is 5060

Backup Outbound
Port

Backup Outbound Proxy’s Service port, default is 5060

Summary of Contents for cnPilot R200
























































































































































Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands

Cambium Networks cnPilot R200, User Manual

Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands