Cambium Networks cnPilot R200 User Manual Download Page 113

Page: 113 / 151

Chapter 3: Advanced Configuration

Administration

Page

111

NTP settings

Table 68 NTP settings

Field Name

Description

NTP Enable

Enable/Disable NTP

Option 42

Enable/Disable DHCP option 42. This option specifies a list of the NTP
servers available to the client by IP address.

Current Time

Display current time

NTP Settings

Setting the Time Zone

Primary NTP Server

Primary NTP server's IP address or domain name

Secondary NTP Server Options for NTP server's IP address or domain name

NTP synchronization

NTP synchronization cycle, cycle time can be 1 to 1440 minutes in any
one, the default setting is 60 minutes

Summary of Contents for cnPilot R200
























































































































































Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands

Cambium Networks cnPilot R200, User Manual

Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands