Cambium Networks cnPilot R200 User Manual Download Page 44

Page: 44 / 151

Chapter 3: Advanced Configuration

Network

Page

If it is left empty, the service name is auto detected.

Operation Mode

Select the mode of operation, options are Keep Alive, On Demand and

Manual:

•

When the mode is Keep Alive, the user sets the 'keep alive redial
period' values range from 0 to 3600s, the default setting is 5
minutes;

•

When the mode is On Demand, the user sets the 'on demand idle
time' value in the range of 0-60 minutes, the default setting is 5
minutes;

•

When the mode is Manual, there are no additional settings to
configure

Keep Alive Redial
Period

Set the interval to send Keep Alive messaging

Summary of Contents for cnPilot R200
























































































































































Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands

Cambium Networks cnPilot R200, User Manual

Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands