Cambium Networks cnPilot R200 User Manual Download Page 79

Page: 79 / 151

Chapter 3: Advanced Configuration

Wireless

Page

Advanced

Table 43 Advanced

Field Name

Description

BG Protection
Mode

Select G protection mode, options are on, off and automatic.

Beacon Interval

The interval of sending a wireless beacon frame, within this range, it will
send a beacon frame for the information of the surrounding radio
network.

Data Beacon
Rate(DTIM)

Specify the interval of transmitting the indication message, it is a kind of
cut down operation, and it is used for informing the next client which is
going to receive broadcast multi-cast.

Fragment
Threshold

Specify the fragment threshold for the packet, when the length of the
packet exceeds this value, the packet is divided.

RTS Threshold

Specify the packet RTS threshold, when the packet exceeds this value, the
router will send RTS to the destination site consultation

Summary of Contents for cnPilot R200
























































































































































Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands

Cambium Networks cnPilot R200, User Manual

Search results

Summary of Contents for cnPilot R200

Reviews:

Related manuals for cnPilot R200

Brands by name

Popular brands