27
38
PROGRAMMING
FEATURE ‘IV” PROGRAMMING:
Turn the Ignition ‘switch “
ON/OFF” (3) TIMES
and leave in the
“OFF”
position.
Push the Program switch (8) times and hold in on the 8th push
until (4) chirps with a long chirp is heard then release the Program
switch. You are now in the Start feature “
IV
” programming mode.
Press and release the transmitter button that corresponds to the
feature you desire to program.
FEATURE CHART #IV
Press
Transmitter
Button
One Chirp
with One LED
Pulse Factory
Default
Setting
Two Chirps
with Two LED
Pulses
Three Chirps
with Three
LED Pulses
Four Chirps
with
Four LED
Pulses
1
Exit the programming mode. (3 long chirps and 3 parking light
flashes to confirm this exit.)
2
Engine Check-
ing Voltage
Engine Check-
ing TACH / RPM
Learning Mode
3
Start Timer:
0.6-second
0.8-second (2chirps), 1.0-second (3 chirps) 1.2-
second (4 chirps), 1.4 – second (5 chirps) 1.6-sec-
ond (6 chirps), 1.8-second (7 chirps), 2.0-second
(8 chirps), 3.0 second (9 chiprs), 4.0 –second (10
chirps)
4
Hi Check Level
Low Check
Level
Exit: Press the button on the transmitter. (3) long horn chirps and
(3) parking light flashes to confirm exit.
ENGINE CHECKING TACHIRPM LEARNING:
IMPORTANT NOTE: You must Disarm the “Tach Signal” before
trying to remote start.
Turn the Ignition switch
“ON/OFF” (3) TIMES
and leave in the
“OFF”
position.
Push the Program switch (8) times and hold in on the 8th push until
(4) chirps with a long chirp is heard then release the Program switch.
Press and release the transmitter and buttons at the same
time the LED will flash twice and the horn will chirp twice to con
-
firm the system is in ‘RPM Learning mode”.
1.
2.
3.
1.
2.
3.
+
OPERATION
D. CAR LOCATOR
Press the button twice to active car locator function. The horn will
chirp (6) times. The parking light will flash (12) times, for you to easily
locate your car.
E. PANIC FUNCTION:
The transmitter can be used as a remote panic switch to manually trigger
the alarm in case emergency.
Press and hold the button for (3) seconds. The horn (if installed)
will immediately sound.
During panic mode, the normal function of this transmitter button
will be suspended.
To stop the alarm, press and hold button on the transmitter again
for (3) seconds.
If the button is not pressed, the alarm will automatically stop after
30 seconds.
F. DOME LIGHT CONVENIENCE DELAY & SUPERVISION
Upon disarming, the interior light will remain on for 30 seconds.
Note: Turning on the ignition switch or locking the vehicle’s door will turn
off the dome light.
G. IGNITION CONTROL DOOR LOCK/UNLOCK
If the vehicles door locks have been interfaced to the system, the system
will automatically lock the vehicle’s doors when the ignition is turned
“ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”.
H. TRUNK RELEASE (CHANNEL 3) OUTPUT.
Press and hold button on the transmitter for (2) seconds to operate
the trunk release or other electric devices.
I. DRIVER PAGING / LOST & FOUND
(For two-way transceiver operation only)
It is useful in the event that someone wants to page the driver
of the parked vehicle or someone cannot find his LCD remote
control transceiver. With the ignition switch “off”, press and
hold the valet switch for (2) seconds to page the driver, one
chirp sound shall be emitted from the vehicle and the paging
melody sound continues sounding from the Remote LCD trans-
ceiver and indication flashes on the LCD screen.
1.
2.
3.
4.
Summary of Contents for DELUXE 200B
Page 1: ......
