41
24
PROGRAMMING
ALARM FEATURE. #1 PROGRAMMING:
Turn the Ignition switch from
“ON” to “OFF” (3) times
and leave in
the
“OFF”
position.
Push the programming switch
(2) times
and on
2nd
push hold it until
(1) chirp
followed with a long chirp is heard, then release the switch.
You are now in the
“alarm feature #1 programming mode”.
Press and release the transmitter button that corresponds to the
feature you desire to program.
a. The amount of horn chirps and LED pause will indicate the previous setting.
b. The factory default settings will always be (1) LED flash and
(1) horn chirp.
Press the transmitter button again to change the feature. Simply
keep pressing the transmitter button until the module advances to
vour desired programming setting.
Example:
a. After you hear
(1) chirp
, press the button again and the module
will advance to
(2) LED flashes
and
(2) horn chirps
.
b. Press the button again, the module will advance to
(3) LED flash
and
(3) horn chirps
etc.
FEATURE # I PROGRAMMING CHART
Press
Transmitter
Button
One Chirp
with One LED
Pulse Factory
Default
Setting
Two Chirps
with Two LED
Pulses
Three Chirps
with Three
LED Pulses
Four Chirps
with
Four LED
Pulses
1
Chirps On
Chirps Off
2
0.8 second
door lock pulse
3.5 second
door lock pulse
Double pulse
unlock
Door lock
with “Comfort
Feature”
Five Chirps = 0.8 second Lock, double 0.8 second Unlock
Six Chirps = Double 0.8 second Lock, 0.8 second Unlock
Seven Chirps = Door lock with “Comfort Feature”
3
Ignition con-
trolled door
lock and unlock
Ignition
controlled door
locks only
Ignition
controlled door
unlock only
Without igni-
tion controlled
door lock and
unlock
4
Without this
feature
Door lock
Before start
Door lock after
shut down
Door lock be-
fore start and
door lock after
shut down
Exit: Turn Ignition to “ON” position, or leave it for 15 seconds. (3) long horn
chirps and (3) parking light flashes to confirm exit.
1.
2.
3.
4.
OPERATION
Rapidly depresses the button. The parking light will flash (3)
times. The siren or horn chirps (3) times. The vehicle is now pro-
grammed to start every 2 or 3 hours.
Press the brake pedal to stop the vehicle running.
Exit the timer start:
Timer start can be exited manually as follows:
Make sure the remote start system is not operating the engine.
Turn the ignition on. The LED and parking light will flash (4) times.
The horn chirps (4) times.
Or
Press the button twice to remote start the vehicle. As soon as the
vehicle is running and the parking light have turned on or flashing.
Immediately depress the button then press and hold the* button for
(2) seconds. The parking light will flash (4) times. The siren or horn chirps
(4) times. The vehicle is no longer programmed to start automatically.
E. TO TURN OFF THE REMOTE START:
When the engine is running (by remote start), if you want to stop it,
Press button twice on the remote transmitter under
remote start mode.
Move the optional remote start enable toggle switch to
OFF position. (If installed)
Press the brake pedal.
The vehicle will shut down and turn off the parking light to
indicate engine stopped.
F. SHUT-DOWN INPUT FOR REMOTE STARTER:
If any of the following conditions exist while the system is operating, the
engine will not start or will shut down immediately:
The hood is opened.
The brake pedal is pressed.
Engine is over-revved. (“Tachometer checking type” only)
The pre-programmed run time (5 110 / 20 / 30 minutes) has elapsed.
Press button twice on the remote transmitter under remote start
mode.
Move the optional remote start enable toggle switch to OFF position.
(If installed)
The vehicle refused to start running after (3) unsuccessful attempts.
3.
4.
1.
2.
1.
2.
1.
2.
3.
1.
2.
3.
4.
5.
6.
7.
Summary of Contents for DELUXE 200B
Page 1: ......
