Brother HL-1070 - B/W Laser Printer Service Manual Download Page 188 | Manualshive

Page: 188 / 244

background image

USER’S GUIDE

3–6

✒

Note

To set the Page Protection to A4, Letter or Legal paper sizes, the
following total capacity of memory is required.

300 dpi 600 dpi

Letter/A4 2 Mbytes 6 Mbytes
Legal 3 Mbytes 6 Mbytes

If your printer does not have enough memory for page protection, your
document may be printed at 300 dpi.

You can set this function in the following ways.
The supplied printer driver for Windows 95/98/3.1

The supplied RPC program for DOS
For details of the settings, see the relevant help screen.

APT (Advanced Photoscale Technology)

APT allows your printer to produce fine gray scales to improve the
appearance of documents containing photographic images.
Using this feature, the image is printed in 256 shades of gray at near
photographic quality.

This setting can be made by using the supplied Windows driver. Also, a
demo file which can be opened within Windows Write is included on the
supplied disk. Try printing it with the APT feature.

For details of the settings, see the relevant help screen of the RPC or
Windows driver.

✒

Note

APT is a simpler feature than 1200 x 600 dpi for Windows DIB graphics.
APT does not required so much memory as the 1200 x 600 dpi resolution
setting.

«
...
186
187
188
189
190
...
»

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070 - B/W Laser Printer

Brand: Dascom Pages: 138

Brand: Dascom Pages: 166

Brand: JCM Pages: 22

Brand: Canon Pages: 2

Brand: Canon Pages: 2

Brand: Durst Pages: 2

Brand: Konica Minolta Pages: 15

BIO X Autocalibration Kit

Brand: Cellink Pages: 17

Brand: Savin Pages: 6

Brand: idp Pages: 104

Brand: QuickLabel Systems Pages: 122

Brand: Lexmark Pages: 9

Brand: Oce Pages: 90

Brand: Xante Pages: 31

ECOSYS P5021cdw

Brand: Kyocera Pages: 31

Brand: Tinkerine Studio Pages: 17

Brand: DNP Pages: 10

Brand: Canon Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands