Brother HL-1070 - B/W Laser Printer Service Manual Download Page 184

Page: 184 / 244

USER’S GUIDE

3–2

Data (Toner) Lamp

The

Data

lamp indicates the current status of the print data process.

Lamp Printer status

Off

❍

The printer has no print data.

Blinking

❍↔●

The printer is receiving data from the computer or
the printer is processing data in memory.

●

Print data remains in the printer memory. If the

Data

lamp is on for a long period of time and

nothing has printed, you need to press the switch
to print the remaining data.

This lamp also works as the

Toner

lamp with the

Alarm

lamp. They

blink simultaneously to indicate a toner error. See

“REPLACING THE

TONER CARTRIDGE”

in Chapter 5 and

“Operator Calls”

in Chapter 6.

Drum Lamp

The

Drum

lamp indicates the drum unit is nearly at the end of its life.

Lamp Printer status

Off

❍

The drum unit can be used.

●

The drum unit is nearly at the end of its life.
Installing a new drum unit turns off this lamp. See

“REPLACING THE DRUM UNIT”

in Chapter 5.

Feeder Lamp

The

Feeder

lamp indicates that the rear sheet feeder 2 is selected through

your software. When the front sheet feeder 1 is selected, the lamp is
turned off.

Lamp Printer status

Off

❍

Feeder 1 is selected.

●

Feeder 2 is selected.

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Search results

Summary of Contents for HL-1070 - B/W Laser Printer

Reviews:

Related manuals for HL-1070 - B/W Laser Printer

Brands by name

Popular brands

Brother HL-1070 - B/W Laser Printer, Service Manual

Search results

Summary of Contents for HL-1070 - B/W Laser Printer

Reviews:

Related manuals for HL-1070 - B/W Laser Printer

Brands by name

Popular brands