Brother HL-1070 - B/W Laser Printer Service Manual Download Page 92

Page: 92 / 244

IV-28

Drum

Feeder2

Alarm

Ready

(Paper)

Data

(Toner)

Paper eject sensor

Registration sensor

Cover sensor

Toner sensor

Switch

Fig. 4.8

Paper eject

ON (Paper is detected.)

Drum lamp ON

sensor

OFF (No paper is detected.)

Drum lamp OFF

Registration

ON (Paper is detected.)

Alarm lamp ON

sensor

OFF (No paper is detected.)

Alarm lamp OFF

Cover

ON (The top cover is closed.)

Ready lamp OFF

sensor

OFF (The top cover is open.)

Ready lamp ON

Toner

ON (The toner cartridge is installed.)

Data lamp OFF

sensor

OFF (No toner cartridge is installed.)

Data lamp ON

The procedure for the factory inspection mode is as follows.

(1)

Turn the printer power switch OFF, open the top cover, and remove the drum unit.

(2)

Turn the printer power switch ON while holding down the control panel switch. The
Drum lamp comes ON.

(3)

Lightly press the panel switch again.

(4)

Check that the Drum(paper eject sensor) and Alarm(registration sensor)
lamps go OFF after all the lamps have been ON.

If the paper eject sensor is ON at this point, the Drum lamp stays ON (error).

If the registration sensor is ON at this point, the Alarm lamp stays ON (error).

(5)

Install the drum unit.

Check that the Data lamp goes OFF.

(6)

Lightly touch the registration sensor actuator.

Check that the Alarm lamp comes ON.

(7)

Close the top cover.

Check that the Ready lamp goes OFF.

(8)

Press the control panel switch.

(9)

If all the sensors are correct, the printer goes back to the Ready status. If
any error is detected, the corresponding lamp stays ON.

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Search results

Summary of Contents for HL-1070 - B/W Laser Printer

Reviews:

Related manuals for HL-1070 - B/W Laser Printer

Brands by name

Popular brands

Brother HL-1070 - B/W Laser Printer, Service Manual

Search results

Summary of Contents for HL-1070 - B/W Laser Printer

Reviews:

Related manuals for HL-1070 - B/W Laser Printer

Brands by name

Popular brands