Brother HL-1070 - B/W Laser Printer Service Manual Download Page 40 | Manualshive

Page: 40 / 244

background image

II-24

2.5.5 Drum Cleaning Stage

In the image transfer stage, not all the toner on the photosensitive drum is transferred
onto the paper but some remains on the drum. In the drum cleaning stage, the drum
surface is cleaned by the cleaning roller, so that residual toner on the drum surface is
removed and collected on the cleaning roller itself. The residual toner on the cleaning
roller will be discharged to the drum when starting or non-printing time. The toner will be
collected by the developing roller and reused (for further developing).

2.5.6

Erasing Stage

Before the cleaning stage, the drum surface is exposed to the light emitted from the
erase lamp. (LED lamp) This stage prepares the drum by decreasing its surface voltage
uniformly, ready to receive uniform change in the primary charging stage.

2.5.7

Fixing Stage

An image transferred on paper by static electricity is fixed by heat and pressure when
passing through the heat roller and the pressure roller in the fixing unit. The thermistor
ASSY keeps the surface temperature of the heat roller constant by detecting the surface
temperature of the heat roller and turning on or off the halogen heater lamp.

,

,

,,,

,,,,

,,,

,

,,

,,,,

,,,,,

,,,,,

,,,,

,,

,

,,,

,,

,,

,,,,

,,

,

,

,

,

Fig. 2.31

Pressure roller

Thermistor ASSY

Halogen heater lamp

Heat roller

Cleaner ASSY

«
...
38
39
40
41
42
...
»

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070 - B/W Laser Printer

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 97

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 151

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 120

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 97

SCX 4200 - B/W Laser - All-in-One

Brand: Samsung Pages: 95

SCX 4500 - B/W Laser - All-in-One

Brand: Samsung Pages: 172

ProXpress M337x

Brand: Samsung Pages: 56

PROXPRESS M332 SERIES

Brand: Samsung Pages: 50

ML-2240 - 23 Ppm Mono Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 8

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 134

ML-1610 - B/W Laser Printer

Brand: Samsung Pages: 112

Brand: Samsung Pages: 128

Brand: Samsung Pages: 152

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 207

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 237

ML 3471ND - B/W Laser Printer

Brand: Samsung Pages: 103

ML 2150 - B/W Laser Printer

Brand: Samsung Pages: 217

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands