Brother HL-1070 - B/W Laser Printer Service Manual Download Page 170 | Manualshive

Page: 170 / 244

background image

USER’S GUIDE

1–6

OPERATING AND STORAGE ENVIRONMENT

Please take note of the following before using the printer.

Power Supply

Use the printer within the specified power range.

AC power:

±10% of the rated power voltage in your country

Frequency:

50 Hz (220 V– 240 V) or 50/60 Hz (110–120 V)

The power cord, including extensions, should not exceed 5 meters (16.5
feet).

Do not share the same power circuit with other high-power appliances,
particularly an air conditioner, copier, shredder and so on. If it is
unavoidable that you must use the printer with these appliances, it is
recommended that you use an isolation transformer or a high-frequency
noise filter.

Use a voltage regulator if the power source is not stable.

Environment

The printer should be installed near a power outlet, which is easily
accessible.

Use the printer only within the following ranges of temperature and
humidity.

Ambient temperature:

10°C to 32.5°C (50°F to 90.5°F)

Ambient humidity:

20% to 80% (without condensation)

The printer should be used in a well ventilated room.

Place the printer on a flat, horizontal surface.

Keep the printer clean. Do not place the printer in a dusty place.

Do not place the printer where the ventilation hole on the right hand side
of the printer is blocked.

Do not place the printer where it is exposed to direct sunlight. Use a blind
or a heavy curtain to protect the printer from direct sunlight when the
printer is unavoidably set up near a window.

Do not place the printer near devices that contain magnets or generate
magnetic fields.

«
...
168
169
170
171
172
...
»

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070 - B/W Laser Printer

Brand: Zeka Pages: 54

Brand: Unisys Pages: 255

Brand: Xerox Pages: 199

Brand: Oki Pages: 100

Brand: Oki Pages: 2

Brand: Xerox Pages: 316

Brand: Xerox Pages: 74

Brand: Xerox Pages: 306

Brand: Xerox Pages: 16

Brand: Xerox Pages: 4

Brand: Oki Pages: 38

Brand: Oki Pages: 38

Brand: Oki Pages: 36

Brand: Oki Pages: 36

Brand: D-Link Pages: 12

Brand: Panasonic Pages: 102

Brand: DataCard Pages: 2

Brand: 3Doodler Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands