Brother HL-1070 - B/W Laser Printer Service Manual Download Page 150 | Manualshive

Page: 150 / 244

background image

- 20 -

Using the Printer Status Monitor Program

Type

C:\RPCX>STMX

and press the Enter key to make the Printer Status Monitor Program

stay resident in your computer memory. If there are any changes to the printer status, it
displays a message on your computer screen.

If the printer status monitor program stays resident in your computer, you can monitor the
printer status on your computer screen immediately using the hot-key sequence (Ctrl+Alt+R).

To remove the Printer Status Monitor program from your computer memory, type

C:\RPCX>STMX/R

and press the Enter key.

❏

The RPC works in the environment where your printer is directly connected to your
computer. If you are using any printer buffer switches which do not support bi-directional
communication between the printer and computer, the program works only in the PC to
printer direction and cannot receive printer status information.

❏

The program does not work with printers on a network.

❏

If the RPC conflicts with some application software, exit your application software and
then run the RPC.

❏

The RPC may work in the DOS-compatible box screen mode of Windows, however, it is
recommended that you completely exit from Windows to the DOS prompt before using the
RPC.

❏

The Printer Status Monitor and some other Terminate-and-Stay programs cannot coexist in
the computer’s memory. If they do not work properly together, use them one at a time.
You can suspend the Printer Status monitor with any of the following methods or
commands.

Type

C:\RPCX>STMX/R

and press the Enter key.

Hold the space bar down while executing the AUTOEXEC.BAT file at DOS startup to
prevent the status monitor being loaded as a TSR program.

«
...
148
149
150
151
152
...
»

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070 - B/W Laser Printer

Brand: 3D Systems Pages: 26

Brand: 3D Systems Pages: 39

WorkSeries 200 Series

Brand: 3D Platform Pages: 9

Brand: Oki Pages: 4

VarioPrint 6000 MICR series

Brand: Oce Pages: 264

Brand: Oce Pages: 194

Brand: Xerox Pages: 418

WORKCENTRE 5755

Brand: Xerox Pages: 356

Brand: Ricoh Pages: 159

Brand: VuPoint Pages: 20

Digital Color Press 700

Brand: Xerox Pages: 216

Brand: W2P Engineering Pages: 40

Brand: Xiamen Hanin Electronic Technology Pages: 27

Brand: LaserLine Pages: 14

DocuPrint 4635 IPS Series

Brand: Xerox Pages: 16

Brand: Kyocera Pages: 410

10600 - Stylus Pro Color Inkjet Printer

Brand: Epson Pages: 8

Brand: Epson Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands