Brother HL-1070 - B/W Laser Printer Service Manual Download Page 161 | Manualshive

Page: 161 / 244

background image

USER’S GUIDE

Radio Interference (220-240 V Model Only)

This printer complies with EN55022(CISPR Publication 22)/Class B.

Before this product is used, ensure that you use a double-shielded cable with twisted-
pair conductors and that it is marked “IEEE 1284 compliant”. The cable must not
exceed 1.8 meters in length.

Laser Safety (For 110–120 V Model Only)

This printer is certified as a Class I laser product under the U.S. Department of Health and
Human Services (DHHS) Radiation Performance Standard according to the Radiation Control
for Health and Safety Act of 1968. This means that the printer does not produce hazardous
laser radiation.

Since radiation emitted inside the printer is completely confined within protective housings
and external covers, the laser beam cannot escape from the machine during any phase of user
operation.

FDA Regulations (For 110-120 V Model Only)

U.S. Food and Drug Administration (FDA) has implemented regulations for laser products
manufactured on and after August 2, 1976. Compliance is mandatory for products marketed
in the United States. One of the following labels on the back of the printer indicates
compliance with the FDA regulations and must be attached to laser products marketed in the
United States.

MANUFACTURED:
BROTHER INDUSTRIES (USA) INC.
2950 Brother Blvd., Bartlett, TN 38133, U.S.A.
This product complies with FDA radiation performance standards, 21 CFR Subchapter J

MANUFACTURED:
BROTHER INDUSTRIES LTD.
15-1 Naeshiro-cho Mizuho-ku Nagoya, 467-8561 Japan
This product complies with FDA radiation performance standards, 21 CFR Subchapter J

Caution

Use of controls, adjustments or performance of procedures other than those specified in this
manual may result in hazardous radiation exposure.

«
...
159
160
161
162
163
...
»

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070 - B/W Laser Printer

Brand: DataCard Pages: 17

Brand: DataCard Pages: 24

Brand: Labelmate Pages: 2

Brand: LabelTac Pages: 15

Brand: Oki Pages: 28

Brand: Oki Pages: 22

image RUNNER 3045

Brand: Canon Pages: 14

Brand: Oki Pages: 512

Brand: Samsung Pages: 368

Brand: FujiFilm Pages: 37

ProJet x60 Series

Brand: 3D Systems Pages: 72

Brand: Intuitive Pages: 18

Brand: Oki Pages: 8

Brand: B-G Instruments Pages: 2

THERMOMARK CARD

Brand: Phoenix Contact Pages: 35

Brand: Oki Pages: 138

D-color MF 250 Plus

Brand: Olivetti Pages: 276

Brand: Xerox Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands