Brother HL-1070 - B/W Laser Printer Service Manual Download Page 74

Page: 74 / 244

IV-10

I-6

Black vertical streaks

Black and blurred vertical streaks

Possible cause

Step

Check

Result

Remedy

HV.GND

contacts
(Fig.4-5)

Corona failure

Is the corona wire dirty?

Yes

Clean the corona
wire with the wire
cleaner.

➇

Corona failure

Is the vertical block streak
about 10mm wide?

Is the corona wire cleaner not
in its home position?

Yes

Return the wire
cleaner to its home
position.

Dirt in the paper
feed system

Is the paper tray or feed
system on the drum unit soiled
with toner?

Yes

Clean the toner off.

Scratch on the
drum

Is the drum surface scratched?

Yes

Replace the drum
unit.

Cleaning failure

Is the drum surface dirty with
toner in streaks?

Yes

Replace the drum
unit.

Scratch on the
heat roller

Is the surface of the heat roller
scratched?

Yes

Replace the fixing
unit.

Note:

Is you print the same pattern continuously, the drum will be worn away and
black vertical streaks appear on the paper.

I-7

Black and blurred horizontal stripes

Possible cause

Step

Check

Result

Remedy

Scratch on the
drum

Are the horizontal stripes at
94mm (OPC drum) intervals?

Yes

Replace the drum unit.

Toner stuck on
the developer
roller

Are the horizontal stripes at
25mm (developer roller)
intervals?

Yes

Print several sheet and see
what happens.

The problem will disappear
after a while. If not, replace the
drum unit.

Scratch on the
fixing roller

Are the horizontal streaks at
63mm (heat roller) intervals?

Yes

Replace the fixing unit.

SR PCB

Is the problem solved after the
SR PCB replaced?

Yes

Replace the SR PCB.

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Search results

Summary of Contents for HL-1070 - B/W Laser Printer

Reviews:

Related manuals for HL-1070 - B/W Laser Printer

Brands by name

Popular brands

Brother HL-1070 - B/W Laser Printer, Service Manual

Search results

Summary of Contents for HL-1070 - B/W Laser Printer

Reviews:

Related manuals for HL-1070 - B/W Laser Printer

Brands by name

Popular brands