Brother HL-1070 - B/W Laser Printer Service Manual Download Page 179 | Manualshive

Page: 179 / 244

background image

USER’S GUIDE

2–8

Two Side Printing (Manual Duplexing)

The supplied printer driver for Windows 95/98 or Windows 3.1 allows
for manual duplex printing from both Feeder 1 and Feeder 2. For more
information about settings, see the help text in the printer driver.

The printer prints all the even numbered pages on one side of the paper
first, and then prints all the odd pages on the reverse side of the paper.

When you have finished printing the even numbered sides of the paper,
the driver instructs you to re-insert the paper by a pop-up message on
your computer screen. Follow the instructions on how to reinsert the
paper.

✒

Note

Before re-inserting the sheets, you have to straighten them, or you will

get paper handling errors.

The use of very thin or very thick paper is not recommended.

If you encounter a double feeding error, we recommend that you hold

all sheets of paper except the front sheet while the paper is feeding.

Fig. 2-8 Notes for Manual Duplexing

✒

Note

When you use the Manual Duplex function, it is possible that paper jams
may occur or print quality might not be satisfactory.

«
...
177
178
179
180
181
...
»

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070 - B/W Laser Printer

Brand: MAKERGEAR Pages: 8

Brand: Panasonic Pages: 9

Brand: Panasonic Pages: 2

Brand: DataCard Pages: 8

Brand: DataCard Pages: 8

Brand: DataCard Pages: 3

WorkCentre 7525

Brand: Xerox Pages: 70

WorkCentre 7525

Brand: Xerox Pages: 8

WorkCentre 7328

Brand: Xerox Pages: 24

WorkCentre 7232

Brand: Xerox Pages: 4

WorkCentre 7232

Brand: Xerox Pages: 24

WorkCentre 7232

Brand: Xerox Pages: 236

WorkCentre 7232

Brand: Xerox Pages: 128

WorkCentre 7232

Brand: Xerox Pages: 25

WorkCentre 7232

Brand: Xerox Pages: 8

WorkCentre 7228

Brand: Xerox Pages: 22

WorkCentre 7228

Brand: Xerox Pages: 300

WorkCentre 7300 Series

Brand: Xerox Pages: 128

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands