Brother HL-1070 - B/W Laser Printer Service Manual Download Page 139 | Manualshive

Page: 139 / 244

background image

- 9 -

Action 4-2: Connect Your Printer to Your Computers using the USB

interface ( Only for HL-1070 with Windows

98 )

The Universal Serial Bus is an interface which allows the printer to be connected to multiple
peripheral devices. If your PC has a USB port, you can connect the printer to your PC by
using the USB interface as described in the following procedure.

✒

NOTE

We recommend that you use the USB interface with this printer on Microsoft Windows
98. Althrough Microsoft Windows 95 OSR2.1 supports the USB interface, some PCs do
not work correctly with the USB interface.

Only one Brother printer can be used in the same chain of the USB connection. If more
than one Brother printer exists in the same chain of the USB connection, only one printer
can be used.

To obtain the latest driver, refer to the following page on our web site:

http://www.brother.com/

[Software]

1

Turn the printer power off.

Connect your PC and HL-1070 with the
USB interface cable.

Turn the printer

power

on.

The dialog shown above will appear on
your PC.

Click the

Next

button.

Select “Search for the best driver for your
device.”

Click the

Next

button.

2

3

«
...
137
138
139
140
141
...
»

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070 - B/W Laser Printer

Brand: LabelTac Pages: 2

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

Brand: Oki Pages: 20

WorkCentre PE120i

Brand: Xerox Pages: 8

Brand: A&D Pages: 8

Ecosys FS-C5300DN

Brand: Kyocera Pages: 35

Jetrix LXi Series

Brand: InkTec Pages: 3

Brand: Ricoh Pages: 84

Brand: Valentin Pages: 32

Brand: Xerox Pages: 6

Brand: DataCard Pages: 106

Brand: Rego Pages: 28

Brand: 2connet Pages: 17

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands