Brother HL-1070 - B/W Laser Printer Service Manual Download Page 180 | Manualshive

Page: 180 / 244

background image

CHAPTER 2 PAPER HANDLING

2–9

MANUAL FEED SLOT

The front multi-purpose sheet feeder 1 also has a manual feed slot. You
can manually load paper sheet by sheet from this slot. You do not need
to remove paper from the multi-purpose sheet feeder when using the
manual feed slot.

❏

When you load one sheet of paper manually:
You do not need to choose manual feed in the Setup dialog box of
your printer driver. While holding the selected size of paper in the
proper orientation (Portrait or Landscape), place the side of the paper
you wish to print on face down into the manual feed slot. Align the
paper at the center of the manual feed slot, and be sure to insert it all
the way. (

➀

) Move the paper guide of the manual feed slot to the

paper width you are using. (

➁

)

Fig. 2-9 Moving the Paper Guide

❏

When you load more than one sheet of paper manually:
Open the Setup dialog box of the supplied Windows printer driver and
choose Manual Feed in the Paper Source section. Follow the above
instructions to load the first page. The printer automatically starts
printing. After the first page is printed, the dialog box appears and
prompts you to load the next page. Load a sheet and choose OK to
resume printing. Repeat these steps until you have finished printing all
the pages.

!

Caution

If bi-directional communications are not operational between the printer
and the computer, such as when the printer is shared on a network, the
dialog box will not appear to load the next page. Manual paper feeding is
not recommended when your printer is attached to a network.

«
...
178
179
180
181
182
...
»

Summary of Contents for HL-1070 - B/W Laser Printer





















































































































































































































































Reviews:

No comments

Related manuals for HL-1070 - B/W Laser Printer

NEFAX - 691 B/W Laser

Brand: NEC Pages: 20

Brand: Grizzly Pages: 56

Brand: Xerox Pages: 418

Liquid Crystal Opus

Brand: PhotoCentric Pages: 12

Brand: TRAK Pages: 98

Brand: Posnet Pages: 2

Brand: Xerox Pages: 20

Brand: EFI Pages: 4

Brand: Nehoc Pages: 9

Brand: Phoenix Contact Pages: 52

490ST - Document Centre B/W Laser Printer

Brand: Xerox Pages: 322

Brand: aqprox! Pages: 52

Brand: Xerox Pages: 4

Brand: Commodore Pages: 188

Stylus Color C70

Brand: Epson Pages: 2

Stylus Color C80

Brand: Epson Pages: 11

Stylus Color C60

Brand: Epson Pages: 3

Stylus Photo 1270

Brand: Epson Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands