Brooks PreciseFlex PFDD4 Reference Manual Download Page 120

Page: 120 / 145

Service Procedures

PreciseFlex™ DDR Collaborative Robots

P/N: PFD0-DI-00010, Rev 5.0.0, April 9, 2022

120

Turn off the robot power and remove the AC power cord.

Remove the foam side cover from the outer link. It is attached with Velcro.

Remove the foam top cover from the outer link. It is attached with Velcro.

Remove the sheet metal cover from the outer link.

Remove cover, slip ring and mount, slip ring.

Remove 6 M2 X 10 SHCS to release gripper, then unplug slip ring connectors in gripper.

At this point you may replace the gripper or the slip ring.

Reassemble parts, be careful not to pinch the slip ring cable, it fits in notch in flange.

The robot does not need to be recalibrated after changing the slip ring or gripper.

Summary of Contents for PreciseFlex PFDD4














































































































Search results

Summary of Contents for PreciseFlex PFDD4

Reviews:

Related manuals for PreciseFlex PFDD4

Brands by name

Popular brands

Brooks PreciseFlex PFDD4, Reference Manual

Search results

Summary of Contents for PreciseFlex PFDD4

Reviews:

Related manuals for PreciseFlex PFDD4

Brands by name

Popular brands