Britax Strider Compact Nstruction Manual Download

Page: 71 / 74

STROLLER FOLDING CONFIGURATIONS

Stroller frame only

Stroller seat

Stroller frame

+ Second seat

Stroller frame + seat

+ Second seat

Second seat

The following are recommended configurations for storage and transportation in a vehicle.

Shown with second seat (optional accessory, sold separately).

Note: The easiest method is to remove the top seat and optional accessories from the

stroller frame and place the accessories and stroller frame into the vehicle separately.

Note: The stroller pivotal handle is required to be place into the regular or

highest lockable position (see section 1.10).
This will prevent the handle from coming into contact with the second seat

and causing damage to the stroller.
If the tension is to hard DO NOT force, re-open the stroller and ensure the

stroller pivotal handle is set to the highest point.

CAUTION:

The stroller can be folded with the top seat and

seat attached to the stroller frame, however, caution must be taken when
lifting the stroller because of the overall weight.

PLEASE REFER TO PAGE 11 FOR LIFTING TECHNIQUES.

Summary of Contents for Strider Compact











































































Search results

Summary of Contents for Strider Compact

Reviews:

Related manuals for Strider Compact

Brands by name

Popular brands

Britax Strider Compact, Nstruction Manual

Search results

Summary of Contents for Strider Compact

Reviews:

Related manuals for Strider Compact

Brands by name

Popular brands