Britax Strider Compact Nstruction Manual Download

Page: 13 / 74

1.4 STROLLER FRAME OPENING

A After carefully removing the contents from

the carton, Lay the frame on a flat surface

and remove any excess packaging.

B With due care, hold the handle with one

hand and with the other hand release the

frame lock. Lift the handle up to partially

open the frame.

C Continue to lift the handle up to open the

frame until the left and right side frame

mouldings engage and lock together.

D Push down on the handle to confirm the

frame is locked open.

IMPORTANT NOTES:

PLEASE REFER TO PAGE 11 FOR SMART LIFTING TECHNIQUES.

•

RELEASE THE STORAGE LATCH WITH DUE CARE AND OPEN THE FRAME.

• WHEN OPENING THE STROLLER, BE AWARE OF THE DANGER OF BEING

INJURED BY MOVING PARTS AND LOCKING DEVICES DURING THE

PROCESS. KEEP ALL HANDS AND LIMBS CLEAR OF THESE PARTS.

• THERE IS POTENTIAL FOR FINGERS OR PARTS OF THE BODY TO BE

INJURED WHEN THE STROLLER IS BEING UNFOLDED, DUE CARE SHOULD

BE EXERCISED.

• KEEP CHILDREN CLEAR OF THE STROLLER DURING UNFOLDING OF THE

STROLLER.

• OPEN THE STROLLER SLOWLY AND BE CAREFUL WHERE YOU PLACE

YOUR HANDS. KEEPING YOUR HANDS ON THE HANDLE ISTHE BEST WAY TO

UNFOLD THE STROLLER.

CAUTION

Summary of Contents for Strider Compact











































































Search results

Summary of Contents for Strider Compact

Reviews:

Related manuals for Strider Compact

Brands by name

Popular brands

Britax Strider Compact, Nstruction Manual

Search results

Summary of Contents for Strider Compact

Reviews:

Related manuals for Strider Compact

Brands by name

Popular brands