Bosch AUTODOME 7000 Operation Manual Download Page 65

Page: 65 / 152

Figure 10.8: In-ceiling (IP54 Rating) Installation Diagram

1 White Trim Ring (factory-installed on

dome bubble)

5 Inner Ring

2 Black Trim Ring (supplied in the

shipping box of the camera)

6 Ceiling (IP54 housing) Gasket

3 Bubble

7 In-ceiling housing

4 Trim Ring Gasket

Place the gasket (provided in the shipping box of the camera) over the top of the in-
ceiling housing.

Carefully slide the gasket down over the housing, until it rests on the flange of the
housing.

Attach Housing to the Interface Box

The In-Ceiling Housing is attached to the Interface Box and secured by two (2) thumbscrews.

9.8

AUTODOME 7000

Installing the In-Ceiling Mount | en

Bosch Security Systems, Inc.

Operation Manual

2014.04 | 2.0 | F.01U.283.679

Summary of Contents for AUTODOME 7000

























































































































































Search results

Summary of Contents for AUTODOME 7000

Reviews:

Related manuals for AUTODOME 7000

Brands by name

Popular brands

Bosch AUTODOME 7000, Operation Manual

Search results

Summary of Contents for AUTODOME 7000

Reviews:

Related manuals for AUTODOME 7000

Brands by name

Popular brands