Bosch Ascenta SHE4AM12U Repair Instructions Download Page 48

Page: 48 / 50

702_58300000130262_ara_en_c

Page 48 of 50

DW Symptoms

(seen

during wash cycles)

Error Code Display

(from cs

test program)

Error Code LED's --

Active / Clean / Sanitized

Solution

Measure voltage between outer most dispenser terminals

(1-3 on e3)

. If

≈

13VDC, replace dispenser. If not, replace operating module.

No drying

No rinse aid

Educate customer on using and refilling rinse aid.

Dispenser rinse aid setting =
0

Set rinse aid setting to “4” if it is at “0”.

Extra Dry Heat

option hasn't

been turned on

Activate

Extra Dry Hea

t option, if it's not activated and is available on the

dishwasher.

Clogged spray arms or filters.

Remove debris / obstructions from filter and spray arms.

Washability issue (heat
pump runs, but dishes
still dirty)

Spray arms not rotating

Make sure spray arms are properly attached and rotate freely.

Make sure spray arms are properly aligned with the supply tube.

Dishwasher won’t start

Door is ajar

Educate customer on closing door securely

(see Section 6.3.1.1)

Heat pump has failed

Replace faulty heat pump

(see section 6.3.1.2)

Drain pump has failed

Replace faulty drain pump

(see section 6.3.1.2)

Summary of Contents for Ascenta SHE4AM12U



















































Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands

Bosch Ascenta SHE4AM12U, Repair Instructions

Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands