Bosch Ascenta SHE4AM12U Repair Instructions Download Page 34

Page: 34 / 50

3. Remove hose clamp to separate pump from adapter

(below left)

4. Disconnect support strap

(below center)

5. To remove pump, slide pump off sump at seal ring

(below

right)

. The seal ring

can’t

be field removed from the heat

pump.

6. Disconnect the two (2) pump wire harnesses

(below left)

To remove the small connector for the sensor harness with
black wires, unlatch it from it’s terminal

(below center)

7. If necessary, remove the adapter by removing four (4)

screws

(below right)

TIP

: The replacement heat pump comes with motor, pump, seal

ring and hose clamp.

NOTE:

The motor can’t be separated from the pump and the

seal ring can’t be field installed.

5.13 Float (safety system)

Tools needed: T20 Torx, #2 Phillips & small flat blade
screwdrivers.

The float is best accessed from the bottom of the dishwasher by
flipping it upside-down or on it’s back. Several plastic pieces
snap into place and must be carefully removed in sequence.

Remove toe kick

– section 5.1.4.1.

Flip dishwasher for access

– section 5.1.6.1.

3. Unscrew one housing screw

(below left)

and push one

cover tab

(below right)

to remove cover from float

assembly.

4. Float lever has tabs which lock onto the knob of the push

rod. Carefully push the push rod knob away from the lever

(below left)

5. Remove the float housing screw

and remove the float

housing with lever

(below center)

6. Remove the wire harness

(below right)

702_58300000130262_ara_en_c

Page 34 of 50

Summary of Contents for Ascenta SHE4AM12U



















































Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands

Bosch Ascenta SHE4AM12U, Repair Instructions

Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands