Bosch Ascenta SHE4AM12U Repair Instructions Download Page 39

Page: 39 / 50

6.1.4.5 Filling error codes

6.1.4.6 Heat pump error codes (circulating)

Digital error codes E:08 – E:13
are shown with one LED
display:

. They have

different causes, such as faulty
heat pump, faulty power
module or insufficient water
supply.

Troubleshooting is needed to
determine the cause.

Digital display

Same LED
display shows
for error codes
E:14 – E:18.

Digital display



E:14

Flow meter error



Code not used (no flow meter)



E:15

Water in base



Code not used (bases are open)



E:16

Volume flow without activation



Code not used (no flow meter)



E:17

Volume flow too high



Water volume too high, safety float

activated



E:18

Volume flow too low



Water volume too low, heat pump

motor load too low.



Check water supply

LED display

Same LED display
shows for error
codes E:20 – E:21.



E:20

Heater error



Heater system check failed;

functional safety error.



Replace heat pump



E:21

Blockage



Heat pump unable to
circulate and clear blockage.



Replace heat pump

LED display

702_58300000130262_ara_en_c

Page 39 of 50

Summary of Contents for Ascenta SHE4AM12U



















































Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands

Bosch Ascenta SHE4AM12U, Repair Instructions

Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands