Bosch Ascenta SHE4AM12U Repair Instructions Download Page 22 | Manualshive

Page: 22 / 50

background image

5.1.3.2 Right side access (power module)

The power module is accessible from the right side.

5.1.4

Pulling out dishwashers

Follow these instructions to pull out dishwashers for side or
bottom front access.

5.1.4.1

To remove toe kick

Tools needed: T20 Torx & #2 Phillips screwdrivers

.

1. Where necessary for access,

remove outer door

–

section 5.1.2.1.

2. Remove two (2) Phillips #2 screws and tilt bottom of toe

kick out and up from dishwasher.

5.1.4.2

Disconnect & pull out dishwasher

Tools needed: T20 Torx & #2 Phillips screwdrivers and pliers or
wrench.

1.

Remove toe kick

– section 5.1.4.1.

2. Disconnect dishwasher mounting brackets

(below left)

.

3. Turn off water and disconnect water line

(below right)

.

4. Turn off electricity and disconnect electric supply by

unplugging power cord or disconnecting wire harness /
loosening strain relief

(below)

.

5. If needed, remove terminal box by loosening two screws at

ends of terminal block, pulling box from dishwasher and
disconnecting harness connector from rear of box

(below)

.

702_58300000130262_ara_en_c

Page 22 of 50

«
...
20
21
22
23
24
...
»

Summary of Contents for Ascenta SHE4AM12U



















































Reviews:

No comments

Related manuals for Ascenta SHE4AM12U

Brand: Samsung Pages: 2

Brand: Samsung Pages: 52

Brand: Samsung Pages: 19

Brand: VESTEL Pages: 16

Brand: Black+Decker Pages: 36

Brand: Iberna Pages: 24

Brand: Maytag Pages: 36

Brand: Listo Pages: 176

Brand: Ariston Pages: 36

Brand: Infiniton Pages: 67

Brand: Daewoo Pages: 41

Brand: Thermador Pages: 66

Brand: Haier Pages: 21

Brand: Haier Pages: 12

Brand: Haier Pages: 28

Brand: Haier Pages: 28

Brand: Haier Pages: 38

DW12-TFE1 series

Brand: Haier Pages: 50

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands