Bosch Ascenta SHE4AM12U Repair Instructions Download Page 40

Page: 40 / 50

6.1.4.7 Drain pump error codes

6.1.4.8 Water switch error codes

6.1.4.9 Aqua sensor error codes

LED display

6.1.5

Customer error codes (Digital display only)

Dishwashers with digital displays have error codes seen by

customers

. Viewing the error code

(Display Failure Memory)

chart, the last two columns (under

“Customer Failure display”

)

show error codes seen by customers in the digital display. The
first two columns (under

“Customer Service Failure display”

)

show error codes seen in the error code program. Error code
displays are identical – the only difference being some service
error codes (e.g. E:08, E:16) can’t be seen by customers.

6.1.6

Clearing error codes

To clear error codes, run the customer service test program.

Same LED display
shows for error
codes E:23 – E:25.

Digital display



E:23

Coil error



System check of drain pump motor

coil failed, functional safety error.



Replace drain pump



E:24

No drain flow possible



Drain pump is running but unable

to remove the water, drain system
blockage.



Check for blockage of drain

hose



E:25

Blockage



Drain pump unable to rotate,

attempts to clear failed.



Check for debris at drain

pump

LED display

Digital display



E:26

Reference cam not detected



Code not used (no water

switch)

LED display



E:28

Calibration failure



Aqua sensor failed to calibrate

702_58300000130262_ara_en_c

Page 40 of 50

Summary of Contents for Ascenta SHE4AM12U



















































Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands

Bosch Ascenta SHE4AM12U, Repair Instructions

Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands