Bosch Ascenta SHE4AM12U Repair Instructions Download Page 36

Page: 36 / 50

FAULT DIAGNOSTICS

6.1

Error codes (service / customer)

6.1.1

Entering error code program

6.1.1.1 SHE “Evolution” models

Press and hold “

” and

Delay

buttons, then turn dishwasher on.

Left program light will flash, 2

program light from left will be lit

and digital display will show “

”). Press “

” button to start

program. Last 8 error codes will show. Press “

” button to scroll

through error codes. Turn dishwasher off to exit program.

To start programs shown with “

”, press “

” button.

6.1.1.2 SHX “Integra“ models

Press and hold “

” and “

”buttons, then turn dishwasher on.

Regular Wash

light will flash and

Quick Wash

light will be lit.

Press “

” button to start program. Only highest priority error code

will show. Turn dishwasher off to exit program.

To start programs shown with “

”, press “

” button.

6.1.2

Error code displays

Error code program *

LED display

Power

Scrub Regular Quick

LED display

Error code program*

Digital display

702_58300000130262_ara_en_c

Page 36 of 50

Summary of Contents for Ascenta SHE4AM12U



















































Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands

Bosch Ascenta SHE4AM12U, Repair Instructions

Search results

Summary of Contents for Ascenta SHE4AM12U

Reviews:

Related manuals for Ascenta SHE4AM12U

Brands by name

Popular brands