manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Installation Manual, Page: 89 / 92

Share
Download
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Installation Manual Download Page 89

AMAX panel 2000 / AMAX panel 2000 EN

 Troubleshooting | en

89

Bosch Sicherheitssysteme GmbH

Installation Manual

F.01U.241.127 | V4 | 2011.12

11

Troubleshooting 

Trouble Causes 

& 

Measures 

No immediate response 

from zone testing right 

after powered up.

–

To work normally, operate the system one minute  after 

powered up.

No indication on keypad 

after  powered up.

–

Check that the AC Mains power and battery fuse are 

correctly connected and work normally.

–

Check the Bosch Bus RBGY are correctly connected.

No response from the 

keypad (Press any key 

sounds error).

–

Check the Bosch Bus RBGY are correctly connected.

–

Enter wrong code more than limit, the keypad is lockout for 

3 minutes.

–

Wrong jumper in using two keypads at the same time.

–

When one keypad is used, the other one can be used only 

30 seconds later.

Can not enter into 

programming mode after 

powered up.

–

Control Panel is in alarm state. E.g. Switch tamper or 24-

Hour zone is still not ready.

–

Control Panel is in arming state. Programming mode can 

only be operated in disarming state.

–

Installer is not enabled from User

No indication on on-board 

LED .

–

AC Mains power or the battery is failed. Restore  the power.

–

The board is damaged. Change a new one.

Zone Leds are always on.

–

Check that the zones are correctly connected.

–

Check that the sensors work normally.

–

Check that the EOL resistor is correctly connected with the 

sensor.

Fault Led is always on /

flashing.

–

Time and date are not set.

–

No battery or the battery is lower than 12V.

–

No siren ( >1,2 K resistor can replace the siren).

–

Telephone number is not correctly programmed.

–

Not connect with the telephone network.

–

Switch tamper is not connected. Otherwise the short 

jumper is connected.

–

Some plug-in module is not used in programming, such as 

DX3010, DX4020 or DX4020G. Refer to Installation Guide 

for detailed measures.

AC Mains power fuse is 

broken.

–

Check the transformer 18V wire is correct.

Over current protection in 

Aux power.

–

Check the 12V Aux power wiring is correct.

–

Check if the Aux power service is higher than 900mA ( top 

limit to control panel). If so, the peripheral is supplied by 

additional power supply.

Aux power can not 

restore after short 

circuited.

–

Restart the AC Mains power and battery.

Summary of Contents for AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Reviews:

No comments