manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Installation Manual, Page: 69 / 92

Share
Download
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Installation Manual Download Page 69

AMAX panel 2000 / AMAX panel 2000 EN

 System Informations 2 | en

69

Bosch Sicherheitssysteme GmbH

Installation Manual

F.01U.241.127 | V4 | 2011.12

8.3

System Event Memory Recall

There are two Event Memorys, one for ALL EVENTS and one for EN EVENTS. Up to 254 system 

events can be recorded in event memory in chronological order. These events are with date 

and time information and stored in non-volatile memory.

For Event records refer toTable 8.1, Page 66.

8.3.1

Keypad Play Back System Events

When Installer Code/Master Code function is used to play back the events, only five system 

events in below table can be shown using the keypad indicators.

Detailed process is as below:

1.

When the Code holder operates the below command:

CODE + [5] + [#]

The system display the above five types of system events.

2.

Other events are not displayed on the keypad.

3.

Each event displays one second and activate the short beep sound on the keypad. The 

events are played bace in reverse chronological order.

Press [#] to exit from the Event Play Back Mode at anytime.

8.4

Output Process

The AMAX panel 2000 / AMAX panel 2000 EN Control Panel has three outputs on the main 

board and 8 outputs on the DX3010 relay module. The Output 1 is used as Siren alarm. During 

the alarm duration, the system can reset the alarm by command “reset” . The other outputs 

can be programmed to follow up different events.

8.4.1

Output Events Option

0 – No output activate for the events

This output doesn’t operate for any events codes. OC outputs are open status. Relay is normal 

open status.

1 – System Disarmed

The output operates on below conditions:

1.

System disarmed after system reset

2.

System operated the disarm command

The output is reset:

1.

When the system is armed

2.

When the output programmed duration is up

2 – System Armed

The output operates on below conditions:

1.

System armed after system reset

System operated the arm command and until system is armed. (When system is operating the 

arm command, the system will arm after the exit delay time is up.)

Event Keypad 

Indication

Zone Alarm or Tamper (Zone1-8)

LED 1-8 light

Tamper Alarm

FAULT Indicator lights

STAY Arming

STAY Indicator lights

AWAY Arming

AWAY Indicator lights

System Disarming

All indicators are extinguished

Summary of Contents for AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Reviews:

No comments