manualshive.com logo in svg

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Installation Manual, Page: 36 / 92

Share
Download
Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Installation Manual Download Page 36

36

en | Fault and Tamper Description

AMAX panel 2000 / AMAX panel 2000 EN

F.01U.241.127 | V4 | 2011.12

Installation Manual

Bosch Sicherheitssysteme GmbH

The fault is reset when the first kissoff tone is received and fault is reset.

Supervise:

1.

Report the fault to configured destination on location 140 when the fault is detected.

2.

Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).

3.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault.

5.6.4

Communication Failure 4

Condition:

Panel can not send the report to the Destination 4 after 4 attempts.

Restore:

The fault is reset when the first kissoff tone is received and fault is reset.

Supervise:

1.

Report the fault to configured destination on location 140 when the fault is detected.

2.

Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).

3.

When the fault is reset, send the restored report to the configured destinations. The 

FAULT indicator is turned off when there is no other system fault.

5.7

Tamper Condition 

The zone indicator 7 lights to indicate Tamper conditions. Enter [7] to step to Tamper 

conditions list for more information.

5.7.1

On Board Tamper 

Onboard Tamper Condition is registered when the Onboard Tamper input (P8) is open.

Condition:  

Onboard Panel Tamper input P8 is open.

Restore:

The Tamper condition is reset when the Input is shorted and Tamper condition is reset.

Supervise:

1.

Report the Tamper condition to configured destination on Location 140 when the 

Tamper Condition is detected.

2.

Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).

3.

When the Tamper Condition is reset, send the restored report to the configured 

destinations. 

5.7.2

Keypad 1 Tamper

Condition: 

Keypad 1 is opened and the Tamper contact is triggered.

Restore:

The Tamper condition is reset when the Keypad is closed and Tamper condition is reset.

Supervise:

1.

Report the Tamper condition to configured destination on Location 140 when the 

Tamper Condition is detected.

2.

Slow flash FAULT indicator (refer the detailed description in chapter keypad indicators).

3.

 When the Tamper Condition is reset, send the restored report to the configured 

destinations. The FAULT indicator is turned off when there is no other system fault.

5.7.3

Keypad 2 Tamper

Condition: 

Keypad 2 is opened and the Tamper contact is triggered.

Restore:

Summary of Contents for AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Reviews:

No comments